AG-3200P-EN.fm Page 12 Wednesday, June 5, 2002 1:43 PM
?
VCR Plus+ Timer Programing
Timer Recording
The PlusCode programing numbers are
the numbers next to the program in
Up to 8 timer recording programs can be made using VCR Plus+
most TV listing.
timer programing, Express timer programing or 24HR Quick
Load a cassette with the record safety
Programing method as far as a year in advance. Remember, the
tab intact. The VCR turns on, and the
clock must be set before you can program the timer.
counter is reset, automatically.
NOTES:
APress PROG. on the Remote to access
I If all the 8 programs have already been set, ?PROGRAM FULL?
the PlusCode No. screen.
appears on the TV screen.
I After timer recording is completed, the VCR turns off PLUSCODE NO.
automatically.
I You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.PRESS NUMBER KEY (0-9)
PRESS (+/-) TO SET
I Even if a power failure occurs, the VCR keeps your timer EXPRESS PROGRAMMING
PRESS (PROG.) TO END
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
BPress the appropriate Number keys
again to this VCR after the power failure, this VCR starts the
to input the PlusCode number, then
Plug&Play setting automatically to restore the clock time and
press OK or e. Check to make sure
channel setting. If the clock time and channel setting are
the setting is accurate on the Program screen.
restored correctly, each timer program you have made will start
PROGRAM 1
at its start time unless its end time has elapsed.PLUSCODE NO. (PLUSCODE NO. 12345678)
I If the tape reaches its end during timer recording, the recording 12345678STARTSTOP8:00PM10:00PM
stops and ? #?, ? ? and ? $? on the display panel blink. Press DATECH
12/24/0212 SP
TIMER to disengage timer, then press STOP/EJECT (0) on TUE
PRESS NUMBER KEY (0-9)
the VCR to eject the cassette or press POWER 1 then press PRESS (8=DAILY, 9=WEEKLYTHEN (OK)
STOP+/- = STOP TIME, SP/EP)
REW (3) on the Remote to rewind the tape.PRESS (PROG.) TO END PRESS (PROG.) TO END
I If the Guide Channel Set screen GUIDE CHANNEL SET
?appears after pressing OK, press the GUIDE CH: 12
Changing VCR Plus+ SettingVCR CH : - - -
Number keys, CH+/- or rt to input
The VCR Plus+ programing system assigns a VCR Plus+ guide
the number of the channel on which
channel to the TV channels and the cable channels. These guide the broadcast for the PlusCode
PRESS NUMBER KEY (0-9)
channel numbers are also called the VCR Plus+ channel codes. OR ( , ), THEN (OK)
number is received on the VCR.PRESS (PROG.) TO END
Most TV listings have a section, usually a chart, indicating the I To set the tape speed, press SP/EP.
guide channel numbers assigned to each station.
I To change the stop time, press STOP+/-.
To ensure that VCR Plus+ timer recording operates correctly, it is I To timer-record daily (Monday-Friday) or weekly serials,
necessary to set the VCR Plus+ ?Guide Channel Set? for each
press DAILY (M-F) (Number key ?8?) or WEEKLY (Number
station.key ?9?). Pressing the button again makes the ?DAILY? or
If you have moved to a different area or if a broadcasting station?s
?WEEKLY? display disappear.
channel number has been changed, perform the following steps to I If you made a mistake, press CANCEL to access the PlusCode
set the correct guide channel number.
No. screen again.
I If an incorrect PlusCode number or the one for a broadcast
AAccess Main Menu screen, then Initial Set screen
already finished has been inputted, ?ERROR? is displayed for
Press MENU on the Remote. Press rt to move the highlight bar
about 5 seconds, then the PlusCode No. screen reappears.
(arrow) to ?INITIAL SET?, then press OK or e.
CPress OK or PROG..
BAccess Guide Channel Set screenI If ?PROGRAM NOT COMPLETED PROGRAM OVERLAP?
Press rt to move the highlight bar (arrow) to ?GUIDE appears, see ?Program overlap warning display? ( pg. 13).
CHANNEL SET?, then press OK or e.DPress TIMER. The VCR turns off automatically and ?#? is
displayed on the display panel.
CInput guide channel numberGUIDE CHANNEL SET
Press rt or the Number keys to select the GUIDE CH: 6
VCR CH : - - -
VCR Plus+ guide channel number as Express Timer Programing
shown in the TV listing, then press OK or Load a cassette with the record safety tab intact. The VCR turns
e. PRESS NUMBER KEY (0-9)
OR ( , ), THEN (OK)on, and the counter is reset, automatically.
PRESS (MENU) TO END
APress PROG. on the Remote to access the PlusCode No. screen.
DInput receiving channel numberGUIDE CHANNEL SET
Press rt or the Number keys to select the GUIDE CH: 6 BPress START+/- once to access PROGRAM 1
VCR CH : 47Program screen.
number of the channel on which the guide STARTSTOP
Press START+/-, STOP+/-, DATE+/- or - -:- -AM- -:- -AM
channel?s broadcasts are received, then DATECH
CH+/- repeatedly to enter the start - -/- -/- -- - - SP
press OK or e. PRESS NUMBER KEY (0-9)
OR ( , ), THEN (OK)time, stop time, date or channel.
I Repeat steps 3333 and 4444 for each instance. PRESS (MENU) TO END PRESS (+/-, SP/EP, 8=DAILY
I Press and hold START+/- or STOP+/- 9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
EReturn to normal screento increase the time in 30-minute
Press MENU on the Remote.intervals.
I To set the tape speed, press SP/EP.
I To timer-record daily (Monday-Friday) or weekly serials,
press DAILY (M-F) (Number key ?8?) or WEEKLY (Number
key ?9?). Pressing the button again makes the ?DAILY? or
?WEEKLY? display disappear.
CPress OK or PROG..
I If ?PROGRAM NOT COMPLETED PROGRAM OVERLAP?
appears, see ?Program overlap warning display? ( pg. 13).
? 12 ?
Page 12June 5, 2002 1:41 pm |
ACEC
